Skip to content

Effects

Each deck has a chain of three effect slots, played one after the other. Eight effects are available: echo, ping-pong echo, reverb, flanger, phaser, filter, gate and bitcrusher. They follow the deck’s tempo, and they can play on the whole track or on one of its stems.

  1. On the deck’s rail, press FX among the pad modes (CUES, LOOP, ROLL… FX, SMPL). The eight pads become the eight effects and the knobs of the effects appear beside them.

  2. Choose a slot with the keys 1, 2 and 3. The pads and knobs act on that slot.

  3. Press a pad: its effect goes into the slot and starts. Press it again to stop it.

  4. Turn MIX, AMOUNT and the second knob, and set the period with ½ and ×2.

A slot key is marked while its effect plays, so you can see at a glance which slots are on. A pad’s bar dims when its effect plays in another slot of the chain. Effects work whether or not the deck is playing, and with either mixer.

A deck’s rail in the FX mode: the eight effect pads with ECHO lit, the slot keys 1, 2 and 3, the FX and DECK keys, the MIX, AMOUNT and TONE knobs, and the period of 1 beat with ½ and ×2

Control What it does
MIX The level of the effect. For the echoes and the reverb, how loud the effect is added to the untouched sound; for the others, how far the sound moves from dry (0 %) to fully processed (100 %).
AMOUNT The effect’s main knob: feedback, room size, depth… (see below).
Second knob Its name changes with the effect: TONE, DAMP, WIDTH, DEPTH, RESO, LENGTH or HOLD. In the middle, the effect sounds as it would without it.
½, ×2 The period, in beats, from 1/8 to 8: the time between echoes, the length of a sweep or of a gate’s cycle.

Each slot keeps its own settings: the effect, the knobs and the period. A new slot starts with an echo at half mix, half amount, the second knob in the middle and a period of one beat.

Pad Effect AMOUNT Second knob Period
ECHO Echo: repeats on the beat, both sides together Feedback: how many repeats TONE: turned down, each repeat comes back duller, like tape; at the top, untouched Time between repeats
PING Ping-pong echo: the repeats bounce from left to right Feedback TONE, as the echo’s Time between repeats
VERB Reverb Room size DAMP: damping of the room, a darker tail turned up No effect
FLANGE Flanger: a sweeping jet sound Feedback WIDTH: how far the sweep goes A sweep lasts four periods
PHASE Phaser: a sweeping notch sound Feedback DEPTH: how wide the sweep is A sweep lasts four periods
FILTER A resonant low-pass sweeping down from the top and back Depth: how far down it sweeps RESO: resonance at the cutoff A sweep lasts four periods
GATE Cuts the sound in rhythm Depth: how quiet the sound gets when the gate closes; fully up, silent LENGTH: how long the gate stays open, from a sixteenth of the period to nearly all of it; half in the middle One open and close
CRUSH Bitcrusher: lowers the resolution Crush: from 16 bits down to 4 HOLD: downsampling, none at the bottom, coarser turned up No effect

The echoes and the reverb are added to the sound: switched off, they stop taking in sound and their tail rings out, as on a mixer’s send. The other effects fade in when switched on and back out when switched off. Changing a slot’s effect starts the new one from silence.

The period follows the deck’s tempo, read from its beat grid: at 128 BPM, a 1-beat echo repeats every 469 ms, and a change of tempo carries the effects along. A gate of a beat or less starts on the beat. A track without a beat grid runs its effects at 120 BPM. See Analysis for the beat grid.

The three slots play in order: slot 1, then 2, then 3, each taking what the one before gives. An echo in slot 1 followed by a filter in slot 2 filters the echoes too.

The FX key beside the slot keys switches the whole chain. Off, nothing of the chain sounds, but each slot keeps its own switch: press FX again and the same effects come back. Use it to drop all the effects on a beat and bring them back together.

Where the chain sits in the deck:

  • On the whole deck, the effects come after the EQ and filter of the software mixer and before the channel fader. The sampler’s sounds go through them too. With an external mixer, they act on what the deck sends to its outputs.
  • On a stem, they act on that part of the track alone, before the EQ.

When the deck’s track is separated into stems, the key beside FX chooses where the chain plays. It reads DECK for the whole track; press it to go through the parts: VOX and INST for a track separated into vocals and instrumental, or VOX, DRUM, BASS and MELO for a track separated into four, then back to DECK.

An echo on VOX alone gives a vocal throw while the beat goes on dry; a gate on DRUM chops the drums only. The rest of the track plays on untouched. If you load a track without that part, the chain goes back to the whole deck.

Each slot answers to the actions Effect 1 on / off (and on, off), Effect 1 on while held, Effect 1: next effect, Effect 1: previous effect, Effect 1: Echo on / off and so on for each effect, Effect 1 level (MIX), Effect 1 amount, Effect 1 second knob (tone, resonance… as the effect has), Effect 1 period (a step halves or doubles it) for an encoder, and Effect 1 period, along the knob and Effect 1: the effect, along the knob for a plain knob. The same for effects 2 and 3. For the whole chain: Effects (the whole chain) and Effects on the next part.

Many controllers have three knobs per effect unit. Prisme gives them two uses, as Mixxx does:

  • With no slot focused, Effect knob 1 is effect 1’s amount, Effect knob 2 effect 2’s, and Effect knob 3 effect 3’s.
  • Press a key mapped to Effect 1 focused on the effect knobs / let go (or 2, or 3): the three knobs now set that slot’s amount, second knob and period. On the screen, that slot is chosen and its key is framed. Press the key again to let it go.

Effect amounts together (super knob) turns the amounts of the three slots at once: build a whole chain of effects up with one knob, and bring it down again.

Soft takeover applies: a controller’s knob only takes a setting over once it reaches the value on the screen. The effect actions are listed with the others in all actions; the command palette (Ctrl K) runs the ones that are keys.