Timecode troubleshooting
Most timecode problems show on the turntable’s panel before you hear them. Open Settings, Turntables, play the record, and look at the scope and the four readings of its panel (see Read the signal). Then find the symptom below.
The REL and ABS buttons are not on the deck
Section titled “The REL and ABS buttons are not on the deck”The deck card shows the mode buttons only when Prisme reads turntables. Check, in Settings, Turntables, that Input (DVS interface) names your interface (with ASIO, that Turntables plugged into the inputs of this driver is on) and that you pressed Apply. The title bar then shows the number of input channels, such as 4 input ch.
The device needs at least two input channels. If it has none, the outputs and the inputs may be two separate devices: on WASAPI, Core Audio and ALSA, choose the inputs under Input (DVS interface), separately from the Output in Audio.
On Android, Prisme has to be allowed to listen to the inputs. If you refused, the settings show allow Prisme to listen to the inputs of the sound card, then apply again.
No signal
Section titled “No signal”The panel reads Signal: none, the scope shows a dot, the Level bar is empty.
- Is the record turning, the needle down?
- Is the turntable plugged into the right inputs: 1-2 for deck A, 3-4 for deck B? Play the other turntable and watch the other panel.
- Is the interface’s switch on phono for a turntable? Is a turntable plugged into a line input without a preamplifier? Its signal is then far too weak, see Phono or line.
- With four decks on a two-turntable interface, deck C reads turntable A and deck D turntable B: the panel of C shows A’s signal.
Weak signal
Section titled “Weak signal”The Level bar barely moves, the signal flickers between locked and unsteady, the track stutters or slows.
- Raise the input gain on the interface, or switch the input to phono.
- Clean the stylus and the record. Dust under the needle weakens the signal and adds clicks.
- Check the cartridge: a worn stylus, or one channel of the cartridge failing, gives a flattened ellipse on the scope instead of a circle.
- Check the cables and the headshell contacts: wiggle them while watching the scope.
The track plays but never finds its position
Section titled “The track plays but never finds its position”Signal reads locked, the speed is right, but Record stays at —, needle drops do
nothing in ABS and the deck never plays on at the end of the record.
The record and the timecode format do not match. The speed comes from the tone of the record, which every side shares; the position comes from the bits pressed in it, which differ. In Settings, Turntables, check Control vinyl: Serato CV02 side A for side A, Serato CV02 side B for side B, Serato control CD for the CD. The format applies to all the turntables at once, so put every record on the same side. Apply after changing it.
The track plays backwards
Section titled “The track plays backwards”The record reads backwards while the platter turns forwards: the left and right cables are crossed. After about five seconds of it Prisme asks, in the turntable’s panel, with a Swap left / right button. Swap the cables, or press the button.
The tempo is a third too fast or too slow
Section titled “The tempo is a third too fast or too slow”The panel’s Speed reads about +1.350× at normal play, or about +0.741×: the turntable
turns at 45 rpm while the deck expects 33, or the other way round. Set Record speed in
the turntable’s panel to the speed the platter turns at.
The scope shows a thick or wobbling ring instead of a thin circle; you may hear a low buzz in THRU.
- Connect the turntable’s ground wire to the ground post of the interface or the mixer.
- Keep the turntable cables away from power cables and power supplies.
- Plug the computer, the interface and the mixer into the same power strip.
- A laptop on its charger can bring hum through a USB interface: try it on battery to find out.
Skipping
Section titled “Skipping”The needle jumps grooves when you scratch or when the booth shakes.
- In ABS the track jumps with the needle; in REL it does not. For heavy scratching, REL keeps the track where it is whatever the needle does.
- Set the turntable’s tracking weight and anti-skate as the cartridge maker says, and keep the turntables level and away from the speakers.
- A short loss of signal is held: Prisme keeps the speed for a moment through a bounce, reading unsteady meanwhile. If the signal stays away longer, the deck slows to a stop, as a record would.
The record feels late
Section titled “The record feels late”Every nudge or scratch reaches your ears after the time the sound card takes to bring the signal in and send the music out. Measure it in Settings, Audio, Latency (see Check the latency), then:
- Use the fastest driver of your system: ASIO on Windows rather than WASAPI, JACK on Linux rather than ALSA through the sound server. Core Audio on a Mac is fast as it is.
- Lower the Buffer in Settings, Audio, one step at a time, until the Dropouts counter in the title bar starts to climb, then go back one step. The title bar shows the length of a period, such as Buffer 2.7 ms.
- Keep the master limiter in mind: it adds 1 ms to the software mixer. Turn off Master limiter in Settings, Mixing only if you keep your levels in check.
See Audio dropouts if lowering the buffer makes the sound crackle.
The deck goes on without the record
Section titled “The deck goes on without the record”The needle reached the end of the timecode: the deck plays on by itself and shows INT. In REL the record takes it back as soon as you put the needle before the end and the platter turns; in ABS press REL or ABS on the deck card. See The end of the record.
Cues, loops or SYNC do nothing
Section titled “Cues, loops or SYNC do nothing”The deck is in ABS: the record decides where the track is, so pads that move it are greyed out and SYNC is unavailable. Switch to REL. See Absolute and relative modes.