Skip to content

Loops, rolls and jumps

Loops, rolls and beat jumps are counted in beats, on the track’s beat grid: a track without a grid has no beat loops, rolls or jumps (check it in Analysis). They all live on the pads, in the LOOP, ROLL and JUMP modes, with the keys that go with each mode on the right of the pads.

A deck playing a 4-beat loop: the loop is a lighter band on the waveform; on the rail in the LOOP mode, the pads 1/4 to 32 with 4 lit, then IN, OUT, ½, ×2, EXIT lit, SLIP and CENSOR

With a record in absolute mode, the record decides where the track is: the pads of these modes are greyed out. In relative mode and internal play, everything here works.

In the LOOP mode, each pad sets a loop of so many beats from where the deck plays:

Pad 1 2 3 4 5 6 7 8
Beats 1/4 1/2 1 2 4 8 16 32

The pad of the loop playing lights. Press it again to leave the loop; press another pad to start a loop of that length from where the deck is.

With quantize on, the loop starts on the nearest beat (a loop shorter than a beat, on the nearest step of its own length), so it stays in time. Without it, the loop starts exactly where you press.

On the waveform, the loop playing is a band of light between two lines. A loop you left stays stored, shown as two dim lines, until you set another one.

Key Deck A Deck B
A 4-beat loop, or out of the loop playing F H
Halve the loop C ,
Double the loop V .

Keys are named as on a US QWERTY keyboard; on another layout, use the keys in the same places. Decks C and D take the keys of A and B with Shift held.

In the LOOP and ROLL modes, the keys beside the pads are:

Key What it does
IN Marks where the next loop starts. It lights until you press OUT.
OUT Ends the loop where the deck is and plays it, from IN. Without an IN, it moves the end of the stored loop here.
½ / ×2 Halves or doubles the loop, keeping its start. Works on a stored loop too.
RELOOP Turns the stored loop back on. If the deck is past its end, it goes back to its start.
EXIT Takes the place of RELOOP while a loop plays: leaves it, and the track plays on.

With quantize on, IN and OUT land on the nearest beat. When OUT lands on a beat the deck has just passed, the deck goes back into the loop at the same place of the beat, so the loop starts in time.

In the other pad modes, an EXIT key appears whenever a loop plays, so you can always leave it.

  1. Choose the LOOP mode on the pads.
  2. Press IN where the loop should start: the key lights and a line marks the place.
  3. Press OUT where it should end: the loop plays at once.
  4. Adjust it with ½ and ×2, or press EXIT to go on with the track.
  5. Press RELOOP later to play it again.

To keep a loop with the track, set a hot cue while it plays: see Saved loops.

With SLIP on, the track carries on underneath while the loop plays: when you leave the loop, the deck lands where the track would have been, as if the loop had never happened. Without it, the track plays on from the end of the loop. See Slip.

A roll is a short loop that plays only while you hold its pad, the track carrying on underneath. Let go, and the deck lands where it would have been. Rolls always work this way, whether SLIP is on or not. In the ROLL mode:

Pad 1 2 3 4 5 6 7 8
Beats 1/16 1/8 1/4 1/2 1 2 4 8

With quantize on, the roll starts on the grid, as a beat loop does. Short rolls (1/16 to 1/4) make stutters and build-ups; longer ones repeat a phrase.

In the JUMP mode, each pad moves the deck by so many beats, back or ahead:

Pad 1 2 3 4 5 6 7 8
Beats -32 -16 -4 -1 1 4 16 32

A jump moves by whole beats, so the deck stays in time. If a loop plays around the deck, it moves along with the jump: a 4-beat loop jumped 4 beats ahead loops the next 4 beats.

Each deck keeps a size, in beats, from 1/16 to 64: 4 at first, then the one you left, kept from one start to the next. It is the length of the jumps and of the loop that the controller actions below use. In the JUMP mode, the keys beside the pads show it, with ½ and ×2 to halve or double it. The loop and jump pads of that size have a bar in the light, so you see which ones match it.

Action What it does
Jump back by the size, Jump ahead by the size Jumps by the deck’s size
Loop of the size / exit A loop of the deck’s size, or out of the loop playing
Halve the size, Double the size Changes the size
Size of the jumps and the loop (a step halves or doubles it) The same on a knob that turns

These actions are for a controller (see Actions); the buttons among them are also in the command palette. Controller profiles can also name a loop, a roll or a jump of any number of beats directly.

Action What it does
Loop in, Loop out, Reloop As IN, OUT and RELOOP
Halve the loop, Double the loop As ½ and ×2
Loop a beat back, Loop a beat forward, Loop moved, a beat a step Move the loop by whole beats
To the start of the loop, To the end of the loop Put the deck at either end of the stored loop
Back to the loop, stopped Turns the stored loop on and stops at its start
Forget the loop Takes the stored loop away
Loop 4 beats / exit As F and H on the keyboard