Skip to content

Absolute and relative modes

A deck handed to its turntable follows the record in one of two modes. In absolute mode (ABS) the record is the track: where the needle sits is where the track plays. In relative mode (REL) the record only gives the speed, and the deck keeps its own idea of where it is, so cues, loops and sync can move it. Two more buttons sit beside them on the deck card: INT, the deck playing by itself, and THRU, the deck playing its inputs.

You switch between them at any time on the deck card, even mid-track. See Hand a deck to its record.

You want to Mode
Play as with real records: needle drops, places found by eye on the record ABS
Use hot cues, loops, beat jumps, the slicer, slip REL
Use SYNC on a deck driven by a record REL
Scratch hard with a needle that may skip REL
Play a real record or a CD player through a deck THRU

The position of the needle on the record is the position in the track. Lift the needle and drop it a minute further in: the track jumps a minute ahead. Spin the record back to the start: the track is back at its start.

Prisme follows the record continuously. Small differences between the track and the record (a fraction of a second) are closed smoothly by speeding the track up or slowing it down for a moment, so nothing clicks; a larger one, a tenth of a second or more, is a needle drop and the track jumps.

Because the record decides where the track is, nothing else can move it:

  • SYNC is unavailable; its button says Sync needs relative mode or internal play.
  • The pads are greyed out in every mode but FX and SMPL: no hot cues, loops, rolls, jumps, slices or cuts. So are the loop keys and CENSOR.
  • The reverse does not play the track backwards.
  • A controller’s jog wheel does nothing.

To match tempos by ear and by eye, next to the deck’s pitch readout an arrow shows the pitch to set on the turntable to match the other deck, such as → +1.20 %. The phase strip between the waveforms tells when the beats drift apart: Off by 1/16 in 12 s, then Off the beat: adjust the pitch. See Sync and beatmatching.

Put the needle down anywhere and the deck follows once Prisme has read where it is, after a short stretch of clean signal. Until then the deck takes the record’s speed only. A position read after a drop is checked over the same stretch before the track jumps there, so a crackle or a scratch on the record does not send the track elsewhere.

The track does not start at the very edge of the record: on the Serato records it starts 28 seconds in (20.7 seconds of music at 45 rpm), on the control CD at once. The grooves before are where you put the needle down; the deck plays silence there, its track waiting at the start, and the music begins when the needle reaches that point. Set another start in the Lead-in (s) field of the turntable’s panel, see Lead-in.

The record gives the speed and the direction only. Where the track is stays the deck’s: a needle drop, or the needle lifted and put back elsewhere, does not move it, the track just goes on from where it was once the record turns again.

Everything that moves the track works on top of the record: hot cues, loops, loop rolls, beat jumps, the slicer, slip, censor and reverse. Press a hot cue and the track jumps there while the record keeps turning; it carries on from the cue at the speed of the platter.

A turntable has its own pitch fader, so SYNC on a record can work two ways. Choose in Settings, DJ, Sync on a record in relative mode:

Choice SYNC
One shot: matches once, the pitch fader keeps working (default) Pressing SYNC snaps the beats onto the leader’s and matches its tempo once. From then on your turntable’s pitch fader changes the tempo from there; the beats are not corrected afterwards.
Locked: follows the leader, the pitch fader is ignored Tap SYNC to lock the deck to the leader’s tempo; hold it to match once instead. Locked, the turntable’s pitch fader no longer changes the tempo, but nudges and scratches on the platter still do. Taking SYNC off gives the tempo back to the turntable’s pitch fader.

In both, the phase stays in your hands once matched: Prisme never pulls the beats back into line behind your back. Loading another track, or changing the record speed, forgets the match. More in Sync and beatmatching.

The deck plays by itself with its own PLAY button, CUE and tempo fader, as without turntables. Choosing REL or ABS again hands it back to the record.

Choosing INT while the record plays, or giving the turntable to the other deck of the pair (see Choose the inputs), does not stop the music: the deck plays on at the record’s tempo, which its tempo fader moves to, and in the record’s direction. A record standing still leaves it stopped.

The deck plays what comes into its inputs, as it comes: a real record, a CD player, any line source. Its track waits where it was. The deck’s effects still act on the sound, and with the software mixer so do its channel strip and fader, so a real record can be mixed in with the rest. Choose INT, REL or ABS to hear the track again; the vinyl settings are left as they were.

When the needle reaches the end of the timecode while the track plays forward (at least at half speed), the deck does not stop with the music: it plays on by itself at the speed the record last had. The deck card then shows INT, and its light says The needle reached the end of the record: the deck plays on by itself. Choose REL or ABS to hand it back to the record.

How the record takes it back depends on the mode:

  • REL: as soon as the needle is back before the end and the platter turns, the record drives the deck again, by itself.
  • ABS: taking it back would make the track jump to where the needle is, so it waits for you. Press REL or ABS on the deck card, or load another track.

The deck stops when its track ends. This only happens once the record has been read before its end since the track was loaded: a track loaded with the needle already in the run-out grooves does not set it off.

The end of the record comes after about 10 minutes on side A at 33 rpm, 15 on side B (see What Prisme reads). Longer tracks either play on by themselves past it, or go on in REL from a needle put back near the start.

Both modes follow the record forwards and backwards, slow or fast, so scratches and backspins sound as they are played. A few things help:

  • Key lock keeps the pitch while the tempo changes, between half and twice the speed; outside that range, during a scratch or a backspin, the track is pitched as a real record would be.
  • Held still under a finger, the track barely sounds, and dragged slowly it is softer, as a needle in a groove. A scratch is at full level.
  • Needle bounces are held: when the signal drops for a moment while the record turns, the speed is kept until it comes back, and the turntable’s panel reads unsteady. Clicks of dust on the record are ignored.
  • In ABS a needle that skips makes the track skip by the same amount. REL ignores skips.
  • For cuts, set the crossfader curve to SHARP in Settings, Mixing, or use a hardware mixer’s own curve.