Recording a mix
Prisme records your set to a WAV file and writes its tracklist next to it when you stop, with the time each track came in. It records the software mixer’s master, or with a hardware mixer, what comes back into your sound card from the mixer’s record output.
Record
Section titled “Record”-
Click Rec in the title bar. It is greyed out while the audio is stopped.
-
Choose what to record:
- Master: what the software mixer plays (only offered with the software mixer).
- Inputs 1-2, Inputs 3-4…: what comes into that input pair of your sound card. Plug your hardware mixer’s record output there. A pair a turntable comes into reads Inputs 1-2: a turntable: it would record the record’s timecode.
-
The key turns red and counts the time. Mix as usual.
-
Click it again to stop (Stop recording). Prisme finishes the file and writes the tracklist.
When it stops
Section titled “When it stops”However a recording ends (from Rec, a controller or the palette, the audio device lost, or Prisme closed), a notice at the bottom of the window tells where it went: Mix saved: and the file’s name, then how long it lasts, in how many files if it was split, and the name of its tracklist. Show in folder opens the folder in your system’s file manager (Explorer, Finder, or your Linux desktop’s), the file selected where it can be. The notice goes away by itself after 15 seconds.
On a phone, which shows no folders, the notice says which folder the recording is in instead.
If the disk filled up or the drive went away while recording, the notice says Mix cut short, saved up to there: with the reason: the file holds what was written until then. If the tracklist could not be written, it says so too.
Hover over Rec afterwards to see again where the last recording went, how long it lasted and how many tracks it holds.
On a phone, Rec at the top opens the same choice, each source with what it holds.
From a controller or the command palette, Record the mix starts and stops a recording without asking. It records what you recorded last, if it is still there and no turntable comes into it now, else the software mixer’s master. With an external mixer, nothing has been chosen until you record its inputs once from Rec: until then Record the mix records nothing and says so (Nothing to record without asking: choose the inputs of your mixer in the Rec menu), rather than record silence or a timecode. Your choice is kept for the next start.
What is recorded
Section titled “What is recorded”Master is the software mixer’s master after the master level and the master limiter, the open microphone and the aux line included. It is taken before the balance, so BAL does not change the recording, and the booth level does not either. The headphones and the preview are never recorded.
Inputs record exactly what reaches that pair, at the level your mixer sends. Set your mixer’s record or booth output so its loudest peaks stay below full scale: Prisme does not limit it.
The file
Section titled “The file”| Format | WAV, stereo, 24-bit, at the sample rate the audio runs at |
| Folder | Prisme Recordings in your Documents folder, out of your music folder so it does not end up in the library |
| Name | The date and time it started: Prisme 2026-10-11 21h30m05.wav |
The file is kept up to date every second while it records, so a crash or a power cut loses a second at most.
A WAV file holds about 4 GB, a little over four hours at 48 kHz. A longer set goes on in a second file,
… 2.wav, then … 3.wav. If the audio restarts during a recording (you change the sound card or the
buffer, or the device is unplugged and comes back), the recording goes on in the next file too.
If the disk cannot keep up, Prisme drops what does not fit rather than holding up the sound; the Rec key’s tooltip then says how many seconds were lost (disk too slow).
The tracklist
Section titled “The tracklist”When you stop, Prisme writes two files next to the recording, with the same name:
- a
.txtfile, one line per track:0:12:40 Artist - Title; - a
.cuesheet, which audio players and editors use to split the recording into its tracks.
The tracklist comes from the set’s history. A track counts as played once it has been heard for 30 seconds on a deck, at a playing speed, and its time is when it started being heard. It gets the artist and title from the track’s tags, or its file name.
A track counts as heard even with its fader down, for instance while you cue it in the headphones
for 30 seconds: edit the .txt or .cue if that happens. With a recording split over several files,
only the .txt tracklist is written, as a CUE sheet describes a single file.