Vinyl control
Vinyl control (DVS, for digital vinyl system) lets a turntable drive a deck. Instead of music, the record on the platter carries a timecode: a steady tone with a sequence of bits pressed into it. Prisme listens to that signal through your sound card and works out, many times a second, how fast the record turns, in which direction, and where the needle sits on it. The deck then plays your track the same way: nudge the platter and the track nudges, scratch and it scratches, drop the needle further in and the track jumps there.
Prisme was built for this first. Its timecode decoder is written from scratch and runs inside the audio engine, so the record and the sound stay together.
What Prisme reads
Section titled “What Prisme reads”Prisme reads Serato timecode:
| Control medium | Name in Prisme |
|---|---|
| Serato Control Vinyl, side A | Serato CV02 side A |
| Serato Control Vinyl, side B | Serato CV02 side B |
| Serato control CD, on a CD player | Serato control CD |
Other timecodes (Traktor, rekordbox, Mixxx’s own) are not supported. One format is chosen for all the turntables at once, so every record you play must carry the same one, on the same side.
The usable part of each medium, at 33 rpm, before the needle reaches the end of the timecode:
| Medium | Usable length at 33 rpm |
|---|---|
| CV02 side A | about 10 minutes |
| CV02 side B | about 15 minutes |
| Control CD | about 15 minutes |
A deck can also treat its record as a 45 rpm one: the track then spreads over more of the groove, so a side holds less of it (about 7 minutes on side A). See Setting up timecode vinyl.
What it does
Section titled “What it does”- Absolute mode (ABS): the needle position is the track position. Needle drops, cues you find by eye on the record, everything as with a real record.
- Relative mode (REL): the record drives the speed only. Hot cues, loops, beat jumps and sync work on top of it.
- INT: the deck plays by itself, as without turntables.
- THRU: the deck plays what comes into its inputs, a real record or a CD player.
- Backspins, scratches and needle bounces are followed; when the needle reaches the end of the timecode while the track plays, the deck plays on by itself instead of stopping.
The modes are explained in Absolute and relative modes.
What you need
Section titled “What you need”Turntables or CD players. Any turntable with a cartridge in good shape, or a CD player for the control CD.
Timecode records. Serato Control Vinyl (CV02, side A or B), or the Serato control CD.
A sound card with a stereo input for each turntable. Each turntable takes a pair of input channels: inputs 1-2 for deck A, 3-4 for deck B. A card with four input channels therefore serves two turntables, and one with eight serves four.
A turntable’s output is a weak phono-level signal. The input has to bring it up: DJ interfaces made for DVS have phono inputs, or a switch per input to set to phono. A card with line inputs only needs a phono preamplifier between turntable and card. A CD player playing the control CD gives a line-level signal and goes into a line input. More on this in Setting up timecode vinyl.
Outputs for the mix. Either each deck on its own output pair, into a hardware mixer (outputs 1-2 for deck A, 3-4 for deck B), or Prisme’s software mixer with the master on outputs 1-2 and your headphones on 3-4. See Mixer.
Two turntables, four decks
Section titled “Two turntables, four decks”With four decks on an interface for two turntables, deck C shares the turntable and the outputs of deck A, and deck D those of deck B. The deck you put on REL or ABS takes the turntable; the other one leaves the record and goes back to INT. With eight inputs, each of the four decks has a turntable of its own. See Choose the inputs.
On a phone or a tablet
Section titled “On a phone or a tablet”On Android, vinyl control works through a USB sound card with inputs plugged into the phone. Android asks whether Prisme may listen to the inputs the first time they are needed; if you refuse, Prisme cannot read the timecode until you allow it and apply the settings again. See Prisme on a phone.